Skip to end of metadata
Go to start of metadata

u-boot

The u-boot version is displayed as the first line on the console during boot-up:

u-boot version

U-Boot 2013.04 (Feb 13 2015 - 17:42:59)

CPU: Freescale i.MX6Q rev1.2 at 792 MHz
CPU: Temperature 34 C, calibration data: 0x5b14f17d
Reset cause: POR
Board: MX6Q/ICO-TTJ500
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment

No panel detected: default to Hannstar-XGA
Display: Hannstar-XGA (1024x768)
In: serial
Out: serial
Err: serial
Found PFUZE100! deviceid=10,revid=11
mmc0 is current device
Net: Calling phydev->drv->config
FEC [PRIME]
Warning: failed to set MAC address

Normal Boot
Hit any key to stop autoboot: 0
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading uImage
6006168 bytes read in 400 ms (14.3 MiB/s)
Booting from mmc ...
reading imx6q-ttj500-ldo.dtb
44273 bytes read in 21 ms (2 MiB/s)
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.17-rt12-1.0.2_ga+g335
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6006104 Bytes = 5.7 MiB
Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Loading Kernel Image ... OK
OK
Using Device Tree in place at 18000000, end 1800dcf0

Starting kernel ...

Linux kernel

The kernel version can be obtained by logging in as root onto the target an entering the command uname -a

kernel version

Linux imx6qttj500 3.10.17-rt12-1.0.2_ga+g33597e3 #1 SMP PREEMPT RT Fri Feb 13 15:39:50 GMT 2015 armv7l GNU/Linux

TransferJet drivers

The TransferJetTM driver build version is announced during start-up.  It can be found by entering the command dmesg | grep TransferJet

TransferJet driver version

[   11.452836] Toshiba TransferJet(TM) Icoteq Build Version: CS1.3_ico1

TransferJet obex service

The TransferJetTM obex service application version can be found in its log file at /tmp/tjet-service.log:

TransferJet obex service version

Set default path.
### Install driver modules ...
+++ install tososcmn ... OK.
+++ install tosbuscmn ... OK.
+++ install toscnlfit ... OK.
+++ install tosiofit ... OK.
+++ install toscnl ... OK.
### Make device node ...
+++ major number = 247
+++ making CnlFitCtrl device node /dev/CnlFitCtrl0...OK.
+++ making CnlFitCtrl device node /dev/CnlFitCtrl1...OK.
+++ making CnlFitCtrl device node /dev/CnlFitCtrl2...OK.
+++ /dev/CnlFitCtrl is linked to /dev/CnlFitCtrl0
+++ major number = 246
+++ making CnlFitAdpt device node /dev/CnlFitAdpt0...OK.
+++ making CnlFitAdpt device node /dev/CnlFitAdpt1...OK.
+++ making CnlFitAdpt device node /dev/CnlFitAdpt2...OK.
+++ /dev/CnlFitAdpt is linked to /dev/CnlFitAdpt0
Set default path.
### Install driver modules ...
tososcmn module has been already installed...
+++ install tososscsi ... OK.
+++ install tossipipe ... OK.
+++ install tosiosip ... OK.
### Make device node ...
+++ major number = 245
+++ making ScsiPipe device node /dev/ScsiPipe0...OK.
+++ making ScsiPipe device node /dev/ScsiPipe1...OK.
+++ making ScsiPipe device node /dev/ScsiPipe2...OK.
+++ /dev/ScsiPipe is linked to /dev/ScsiPipe0
tjetObexService version: v0.1.0

Python GUI Application

The TransferJetTM obex service application version can be found in its log file at /tmp/pytjet.log:

 

Python GUI version

** Message: pygobject_register_sinkfunc is deprecated (GstObject)

2015-02-15 14:01:44,880 - pytjet_icoteq.__main__ - INFO - Starting PytjetIcoteq 0.1.0

** (pytjet-icoteq:723): WARNING **: Trying to register gtype 'GMountMountFlags' as enum when in fact it is of type 'GFlags'

** (pytjet-icoteq:723): WARNING **: Trying to register gtype 'GDriveStartFlags' as enum when in fact it is of type 'GFlags'

** (pytjet-icoteq:723): WARNING **: Trying to register gtype 'GSocketMsgFlags' as enum when in fact it is of type 'GFlags'
2015-02-15 14:01:45,695 - pytjet_icoteq.config - INFO - Loading config from: builtin defaults, /home/root/gui.conf, command line options
2015-02-15 14:01:45,710 - pytjet_icoteq.__main__ - INFO - Starting TJET core...
2015-02-15 14:01:45,711 - pytjet_icoteq.__main__ - INFO - GTK initialization check None
2015-02-15 14:01:45,711 - pytjet_icoteq.__main__ - INFO - Starting extensions: TjetUI, Button
2015-02-15 14:01:45,881 - pytjet_icoteq.button - INFO - Registered button device gpio-keys.26
2015-02-15 14:01:45,885 - pytjet_icoteq.client - INFO - Started as Obex Client
2015-02-15 14:01:45,889 - pytjet_icoteq.__main__ - INFO - Entering GTK main...